Interested in reviews of Alsament PETG 1 kg Silver? It got 4.0 out of 5 stars from our customers. Find specific customer reviews of Alsament PETG 1 kg Silver below. We will appreciate if you also share your experiences with Alsament PETG 1 kg Silver after purchasing.
Rated 07/04/2026, variant Alsament PETG 1 kg Silver
Verified purchase
The filament is very cheap, I expected the classic alza version reasonable quality for a good price. The price is even lower than one would think, unfortunately the quality goes down with it. The dryer will take care of the initial moisture, but it will not modify the quality. Filament can be used for smaller prints, but for larger ones its problems are more evident, so unfortunately, even for the price it is not worth it and for me never again.
price
high moisture content of the supplied filament
the quality of the filament is generally tragic
0 ×Report
Automatic translation
Jan, Praha
Rated 05/04/2026, variant Alsament PETG 1 kg Silver
Verified purchase
I didn't have a bad time with it, at slow speeds the result is nice. However, during printing it started to lose colour and became translucent, now it is colourless at the end of the spool.
cheap
changed colour to transparent halfway through the roll
0 ×Report
Automatic translation
Martin, Morkovice
Rated 22/03/2026, variant Alsament PETG 1 kg Silver
Verified purchase
Immediately after unpacking the filament shows signs of moisture. Already when booting, you can hear the filament in the nozzle crackle as it gets wet, and you can see signs of waviness on the material leaving the nozzle.
Price
Speed of delivery
Humidity
0 ×Report
Automatic translation
Company
Rated 18/03/2026, variant Alsament PETG 1 kg Silver
Verified purchase
I've never experienced such a bad/wet filament (I've had dozens of kilos from different manufacturers). First photo - pulling out the new vac when it was wet and literally bursting.
Second photo - after 8 hours in the dryer it's better, but obviously it still needs to be dried.
price
wet as never before
0 ×Report
Automatic translation
Martina, Vyšší Brod
Rated 01/03/2026, variant Alsament PETG 1 kg Silver
Verified purchase - review from a price comparison website
It met my expectations
Nothing yet.
0 ×Report
Automatic translation
Jan, Vrbno pod Pradědem
Rated 21/01/2026, variant Alsament PETG 1 kg Silver
Verified purchase
Best PETG within the price tag 300, -
great, cheap PETG
The colour is exactly what I needed
I absolutely don't understand the comments from people here: ) if you can't even make a heat tower (so you know how to print with filament), don't buy it
price
you have to figure out how many degrees to print it at first: ) As for the Prusha printers, I run it at 226 degrees on the nozzle, 90 degrees on the bed, and absolutely without a single problem: )
If the price tag was in the paycheck, I'd buy a pallet of it: )
0 ×Report
Automatic translation
Vladimír, Hořice
Rated 16/01/2026, variant Alsament PETG 1 kg Silver
Verified purchase
Excellent
0 ×Report
Automatic translation
Jan, Dlouhá Třebová
Rated 03/01/2026, variant Alsament PETG 1 kg Silver
Verified purchase
When printing at 245*C it does not work. When the temperature is raised to 255*C it works OK - see attached photo.
Printed on Elegoo Centauri Carbon
Price
Does not work when printing at manufacturer's temperature
0 ×Report
Automatic translation
Filip, Zlonice
Rated 31/12/2025, variant Alsament PETG 1 kg Silver
Verified purchase
After changing the filament from Spectrum to this filament (during one print) one bubble after another, defects in the surface of the part. Filament bought as a quick emergency, but unfortunately I will not buy again.
Recycled coil
Packaging.
Extremely moist (as if someone had thoroughly soaked it before vacuum packing).
It's not even worth the low price.
Worst filament I've ever printed with.
I don't recommend it.
0 ×Report
Automatic translation
Zdeněk, Mistřice
Rated 28/12/2025, variant Alsament PETG 1 kg Silver
Verified purchase
I think the biggest problem with this filament is the dust inside the spool.
cheap
damp (even drying for 2h did not help)
full of dust and dirt
Fragile
I think the dust is also printed into the printed object
0 ×Report
Automatic translation
Try our cookies
Alza.cz a. s., Company identification number 27082440, uses cookies to ensure the functionality of the website and with your consent also to personalisage the content of our website. By clicking on the “I understand“ button, you agree to the use of cookies and the transfer of data regarding the behavior on the website for displaying targeted advertising on social networks and advertising networks on other websites.
